Building materials, materials design and applications : selected, peer reviewed papers from the 4th International Conference on Building Materials and Construction (ICBMC 2019), February 25-28, 2019, Singapore and the 2nd International Conference on Materials Design and Applications (ICMDA 2019), April 13-15, 2019, Tokyo Japan /
Saved in:
| Meeting name: | International Conference on Building Materials and Construction (4th : 2019 : Singapore) |
|---|---|
| Imprint: | Zurich : Trans Tech Publications Ltd, 2019. |
| Description: | 1 online resource. |
| Language: | English |
| Series: | Materials science forum ; volume 972 Materials science forum ; volume 972. |
| Subject: | |
| Format: | E-Resource Book |
| URL for this record: | http://pi.lib.uchicago.edu/1001/cat/bib/12400025 |
Table of Contents:
- Influence of Bottom Ashes from Biomass on Compressive Strength of Concretes
- An Experiment Investigation on Physical and Mechanical Properties of High Strength Concrete with Suitable Admixture
- Improve Light Weight Concrete Characteristics by Adding Paraffin Wax as Moisture Proof
- Effect of Elevated Temperature on Bond Strength of Concrete
- Bond Behavior of Low-Activated High Aluminate Concrete with Reinforcement under Cyclic Load
- Matera Building Stones: Comparison between Bioclastic and Lithoclastic Calcarenites
- Moisture-Density Relationship of Bottom Ash, Lime Stabilized Bangkok Clay as a Potential Pavement Material in Thailand
- An Experimental Study on Effect of Lime and Geogrid in Pavement Thickness
- Influence of Coating on Mechanical Performance of Lap-Spliced Carbon Fiber-Textile Reinforced Mortar (TRM)
- The Influence of Chemical Additives on Strength of Wood-Cement Composite
- Influence of Thickness of Air Gap on Concrete Curing in Formwork with Transparent Cover
- Heat Treatment of Self-Compacting High-Strength Concrete in Cast In Situ Construction Using Infrared Rays
- Numerical Analysis of Punching Shear Failure of Self-Compacting Fiber Reinforced Concrete (SCFRC) Ribbed Slabs
- Structural Effect of Using Steel Fiber Reinforcement on the Punching Shear of Self-Compacting Fiber Reinforced Concrete (SCFRC) Ribbed Slabs
- Influence of the Bauschinger Effect on the Distribution of Residual Stresses in a Thin Hollow Hyperbolic Disc under External Pressure
- Design of Timber Single-Span Beam with Steel Reinforcement
- Compressive Behaviour of Laminated Neoprene Bridge Bearing Pads under Thermal Aging Condition
- A Deployable Brace Model with Joint Clearance and Strut Eccentricity in Seismic Design
- Evaluation for RC Column Confined Partially with Externally FRP Wrapping Sheet Using Nonlinear FE Analysis
- Strength and Deformability of Reinforced Concrete Beams with Indirect Reinforcement in the Form of Welded Meshes in Compressed Zone
- Conical Round Tubes - Preliminary Tests for Use on Lighting Columns
- Mechanical Behaviour of Composite Material Based on Mortar/Natural Fibers (Fique "Furcraea andina") Meshes as External Reinforcement of Concrete Beams
- Study on Dispersion Stability Characteristics of TiO2 Nanoparticles in PCM for Use in Cold Storage Air-Conditioning
- A Study on the Effect of Argon-Oxygen Plasma Treatment on Ultra-Thin Expanded PTFE Membrane
- Morphology, Mechanical and Thermal Properties of Poly(Lactic Acid)/Propylene-Ethylene Copolymer/Cellulose Composites
- Improvement of Poly(Lactic Acid) Properties by Using Acrylonitrile-Butadiene Rubber and Polyethylene-g-Maleic Anhydride
- Anti-Counterfeiting Layer of 2D Colloidal Crystal Based Photonic Material
- Preparation and Photocatalytic Properties of Graphene/SrTiO3 Thin Film Catalyst
- Comparison of Different FEM Software in Terms of Hot Ultrasonic Assisted Machining Technique
- Research on Technology of Welding Aluminum Foil in Pressure Vessel Based on Ultrasonic Rolling Welding
- Investigation of Arc Bubble Affecting the Arc Stability and Improvement of Weld Appearances Using Bubble Constraint Device in Underwater Wet Welding
- Parametric Study of Underwater Laser Welding on 304 Austenite Stainless Steel
- Surface Modification of Steel by Anodic Plasma Electrolytic Boronitriding and Polishing
- Deterioration Characteristics of Overlapping Layers between Al-5Mg Thermal Spray Coating and Heavy-Duty Paint Coating
- Preparation and Drilling Performance of Orderly Arranged Diamond Bit