Recent Advances in Materials Science and Engineering : selected, peer reviewed papers from the international conference on materials science and engineering : recent advances and challanges ICMSE-RAC 2018, March 11-13, 2018 Egypt /
Saved in:
Imprint: | Zurich, Switzerland : Scientific.Net : Trans Tech Publications, [2018] |
---|---|
Description: | 1 online resource. |
Language: | English |
Series: | Key Engineering Materials ; volume 786 Key engineering materials ; v. 786. |
Subject: | |
Format: | E-Resource Book |
URL for this record: | http://pi.lib.uchicago.edu/1001/cat/bib/12020988 |
Table of Contents:
- The Effect of Heating Rate on Texture and Formability of Ti-Nb Stabilized Ferritic Stainless Steel
- Effect of Electroslag Refining on Cleanness, Microstructure and Mechanical Properties of a Newly Developed CrNiMoWMnV Ultrahigh-Strength Steel
- Effect of Friction Stir Processing on the Microstructure and Mechanical Properties of A384 Aluminum Alloy
- Oxidation Characteristics of Porous Nickel Low-Chromium Binary Alloys in Air at 1273K for 100 h
- Crystallographic Texture Investigation of Thick Section Friction Stir Welded AA6082 and AA5083 Using EBSD
- Cyclic Behavior of Reversion-Treated Structures after Different Cold Rolling Reductions in an AISI 301LN Stainless Steel
- Developing High Strength-High Toughness Low Carbon Steel Using Combined V-Ti-Micro-Alloying and Different Thermo-Mechanical Treatments
- Manganese Distribution between Slag and Metal in the Egyptian Blast Furnace
- Effect of Chemistry Modification, Hot Forging and Partitioning on Low Alloy Grade Tool Steel
- Prominent Achievements of Laser Surface Treatment of Martensitic Stainless Steel and Alpha-Beta 6/4 Titanium Alloy
- The Influence of Shielding Gas on Strength of the Laser Welded Thin Sheet Lap Welds
- Comparative Study of Spot Welding and Firiction Stir Spot Welding of Al 2024-T3
- Effect of Thermal Cycle on Microstructure and Corrosion Behavior of Duplex Stainless Steel SAF 2205 Electron Beam Welded Joint
- Surface Treatment of AISI M2 Tool Steel by Laser Melting
- Some Anionic Surfactants as Corrosion Inhibitors for Carbon Steel in Hydrochloric Acid Solution
- Preparation and Characterization of an Emulsion Paint Based on Arghel Extract as an Eco-Friendly Corrosion Inhibitor
- Characterization and Structure Analysis of the Anodic Film Formed on AZ31 Mg Alloy in KOH Alkaline Solution with Various Additives
- Use of Gamma Ray Back Scattering Method for Corrosion Assessment in Insulated Pipes
- Evaluation of the Inhibition Efficiency of a Green Inhibitor on Corrosion of Cu-Ni Alloys in the Marine Application
- Micro-Machining of Nano-Polymer Composites Reinforced with Graphene and Nano-Clay Fillers
- Tool Wear and Form Accuracy in Ultrasonic-Assisted Milling of Soda-Lime Glass
- The Effect of the Structural Parameters of 3D Orthogonal Woven Composites on their Impact Responses under Different Modes of Impact
- Development of a New Glass for both Visible and Near-Infrared Optical Applications
- Cementing Line Configuration of Bioactive Engineered Zirconia Implants (In Vivo Histological Study)
- Nano Titania Reinforced Limestone Cement: Physico-Mechanical Investgation
- Enhancing the Wetting Properties of Polypropylene and Polyethylene Nonwoven Fabrics Using a Cost-Effective Surface Dielectric Barrier Discharge
- Buckling Tests for Laser-Welded Single Corrugated Core
- Empirical Model for Dry Sliding Wear Behaviour of Centrifugally Cast Functionally Graded Al/SiCp Composite
- Bending Strength of Laser-Welded Sandwich Steel Panels of Ultra-High Strength Steel
- Crack Width Estimation Using Feed and Cascade Forward Back Propagation Artificial Neural Networks
- Ballistic Impact Simulation of Proposed Bullet Proof Vest Made of TWIP Steel, Water and Polymer Sandwich Composite Using FE-SPH Coupled Technique
- Failure Analysis of Condensate Pump Shaft in Power Plant
- Mechanical Properties of a "Simple Panel Structure" Manufactured of an Ultra High Strength Stainless Steel
- Design Process of Durable and Lightweight Rally Car Frame from Ultra-High Strength Stainless Steel
- Design and Manufacturing of a Non-Standard Chain Parts for a Scraper Chain Conveyor: A Case Study
- Design for Additive Manufacturing in Extended DFMA Process
- A Short Glance on Metal 3D AM
- In Implementing a Metal 3D AM Machine
- DFAM Based Multi-Material 3D Printing Using Conductive and Flexible Filaments
- Effect of Gas Dilution Ratios and Substrate Temperature on the Structural Transition of a-Si/#956;c-Si Thin-Film Solar Cell Using PECVD
- CH2O Adsorption on M (M = Li, Mg and Al) Atom Deposited ZnO Nano-Cage: DFT Study
- Indoor Radon Levels and Annual Effective Dose in Dwellings of Najran City, Saudi Arabia
- Two-Step Synthesis of Copper Sulfide-Graphene Counter Electrode for CdS Quantum Dot Sensitized Solar Cells
- Effect of Electrodes Material on the Performance of Batch Reactor Using Plasma Enhanced Technique for Wastewater Treatment