Material engineering practice. selected, peer reviewed papers from the 9th International Conference on Material in Engineering Practice IX, June 1213, 2014, Herl'any, Slovak Republic / IX :

Saved in:
Bibliographic Details
Imprint:Zurich, Switzerland : Trans Tech Publications, 2015.
Enfield, New Hampshire : Trans Tech Publications, [date of distribution not identified]
©2015
Description:1 online resource (233 pages) : illustrations
Language:English
Series:Key Engineering Materials, 1662-9795 ; Volume 635
Key engineering materials ; v. 635.
Subject:Materials science -- Congresses.
Material engineering -- Congresses.
TECHNOLOGY & ENGINEERING -- Engineering (General)
TECHNOLOGY & ENGINEERING -- Reference.
Materials science.
Electronic books.
Electronic books.
Conference papers and proceedings.
Format: E-Resource Book
URL for this record:http://pi.lib.uchicago.edu/1001/cat/bib/11305682
Hidden Bibliographic Details
Other authors / contributors:Mihaliková, Mária, editor.
Zubko, Pavol, editor.
ISBN:9783038267294
3038267295
9783038353447
3038353442
Notes:Includes bibliographical references at the end of each chapters and index.
English.
Online resource; title from PDF title page (ebrary, viewed January 13, 2015).
Summary:These are the proceedings of the 9th Scientific-Technical Conference on ""Material in engineering practice, 2014"". Its content was intended to present innovative materials on improving the properties of materials and quality of materials and, also on the degradation of properties during operation. Special attention was paid to the prediction of mechanical and technology materials properties as well as modern methods for testing the characteristics of materials. These are the proceedings of the 9th Scientific-Technical Conference on ""Material in engineering practice, 2014"". Its content was i
Other form:Print version: Material engineering practice. IX. Zurich, Switzerland : Trans Tech Publications, ©2015 225 pages Key engineering materials ; Volume 635 1662-9795 9783038353447
Table of Contents:
  • Changes of Mechanical Properties of AlSi7Mg0.3 Cast Alloy through Filtration
  • Fatigue Properties of Synthetic Nodular Cast Irons
  • The Fractography Analysis of IN 718 Alloy after Fatigue Test
  • The Modified AlSi7Mg0.3 Cast Alloy Mechanical Properties Changes at Different Testing Temperatures
  • The Influence of Severe Plastic Deformation on Structure and Mechanical Properties the Aluminium Alloy EN AW 6082
  • A Study on Sloshing Frequencies of Liquid-Tank System
  • Analysis of New Generation Material Solutions of Lower Structure for Energy Efficient Buildings
  • The Parameters Affecting Strength Calculation of Gears
  • The Analysis of Chosen Material Properties at Thermal Drilling
  • Changing the Hardness Automotive Steels at Different Strain Rate
  • Fluidity Test of Al-Si Alloy Using by Computer Simulation
  • Aberration Problem within the Process of Automation of the Photoelastic Measurement of the Stresses
  • Corrosion Behaviour of Automotive Steel Sheets Depending on the Degree of Deformation
  • Usability of Various LTCC in Microstrip Filters Construction
  • Structure and Properties of Selected Natural Materials
  • Cyclic Test of DP600 Steel under Tension-Compression Load for Different Pre-Strain Levels
  • New Austenitic Creep Resistant Steels for Superheaters of USC Boilers
  • Comparison of Experimental Stamping Punch Machinability Made out of Unconventional Materials
  • Facesheet-Core Interface Delamination in Sandwich Panels
  • Possibilities of Preparing Tools Working in Conditions of Abrasion Wear with the Modification of the Tool Surfaces by Nitridation
  • The Methodic of Testing Using Experimental Equipment
  • Influence of the Strain Rate and Heat Treatment on the Mechanical Properties of Steel Sheets
  • High Temperature Oxidation of 9-12% Cr Materials P91 and P92 in Supercritical Water
  • Cleanness and Mechanical Properties of Steel after Remelting under Different Slags by ESR
  • IF Steel Effect of Rate Deformation on the Fracture Surface Change
  • Microstructure of Agglomerate Produced with Charcoal as Substitution Fuel
  • The Influence of Current Density on Tribological Behavior Ni-Co Electroplated Coatings
  • Analysis of Crack in Kaplan Turbine Blade
  • Calibration Process and Constructions of Extrusion Calibrators
  • A Comparison of Mechanical Properties of Lumbar Bilateral Implants Manufactured by Additive and Conventional Technologies
  • Influence of Welding Parameters on the Quality of Resistance Spot Welded Joints of DP600 Steels
  • Hydrodynamic Analysis of Fluid Effect in Rigid Rectangular Tank due to Harmonic Motion
  • The Methodology for Determining the Springback of Large Metal Stampings
  • A Study of Thickness Change of Spherical Cup Made from TRIP Steel after Hydraulic Bulge Test
  • Steel KODUR 460MC under Creep Condition
  • Analysis of Material Solutions of Exterior Walls with Contact Thermal Insulation System
  • Flexural Properties of FDM Prototypes Made with Honeycomb and Sparse Structure
  • Use of Geopolymer Matrix Composites in the Construction of Fire Doors
  • Influence of Metallurgical Treatment on Properties of Ductile Cast Iron GJS 400-18 LT
  • Selection of Materials for the Body Deformation Zones
  • Corrosion Characteristics of Transit Pipeline API 5L X60
  • The Wear Evaluation of Blasting Machine's Blades
  • Prediction and Verification of Compatibility of MMT Nanofiller in PA6 Matrix
  • Probabilistic Modelling and the k-Value Concept
  • Structural Properties of Ni-Co Electroplated Coatings Studied by X-Ray Micro-Beam
  • Material Criteria for Parts Exposed to Liquid Medium Loading
  • Selected Properties of Composites with Polypropylene after Ageing
  • Analysis of Mechanical Properties of Individual Phases in Steels by Depth Sensing Indentation